Protective Film Factory is an Anti Static Film Manufacturer supplying temporary PE and PET protective films for static-control handling, clean transfer, and short-term storage. This category includes low-tack grades for electronic components, display panels, optical films, and precision parts. Each structure helps reduce static buildup, limit particle pickup during unwinding or peeling, and keep covered surfaces visible before the next production step.
Showing the single result
Choosing an Anti Static Film Manufacturer involves more than comparing a resistance figure. For sourcing teams reviewing China anti static plastic film options, the approved grade should match the actual substrate, surface finish, dwell period, tested side, and conditioning environment. Smooth coated panels, optical films, and lightly textured parts may not respond to the same adhesive grade in the same way. A short trial helps identify edge lift, removal-force changes, or contamination after storage.
Start with the protected surface and identify when static risk is most likely. PET is generally better suited to flat panels, optical films, and precision parts where roll flatness and slit-edge cleanliness matter. PE is more appropriate where flexibility is the priority. When ordering an anti static plastic film roll, state the resistance method, tested side, temperature, humidity, conditioning time, and dwell period. For adhesive-backed grades, compare peel adhesion after dwell, adhesion build, edge stability, particle pickup, and residue on the actual substrate before bulk production. Low tack alone is not a reliable selection rule. The same grade should also be checked again if the coating, storage period, or downstream process changes.
Surface resistance is a useful starting point, but it does not describe every removal-stage risk. For panels, optical parts, and ESD-sensitive component handling, peel-generated voltage should also be evaluated after a defined dwell period on the actual surface. A practical reference evaluation may record 23 C, 50% RH, peel speed, peel angle, measurement distance, and tested side. This separates resistance data from dynamic peeling behavior and makes sample comparisons easier to interpret.
Item | Typical Range / Customizable Value |
Carrier film | PE protective film / PET protective film |
Anti-static structure | Film-side / adhesive-side / double-side treatment |
Appearance | Transparent clear / light identification color |
Thickness | Grade-dependent; select by carrier, surface, and handling route |
Adhesive system | Low-tack acrylic / silicone-based removable adhesive / application-specific option |
Surface resistance | Record grade, tested side, method, temperature, and humidity |
Surface resistivity | Add where required by the ESD specification |
Static decay | Define initial voltage, target level, method, and conditioning |
Peel-generated voltage | Evaluate with substrate, dwell time, peel speed, peel angle, and distance |
Peel adhesion | Test on the actual surface after the required dwell period; use 180-degree peel where applicable |
Particle pickup | Observe during unwinding, application, and peeling |
Clean removal | Inspect residue, contamination, ghosting, and surface change |
Transparency | Test haze or transmittance where required |
Roll width and length | Custom slit width and roll length according to equipment |
Core size | Match the unwinding equipment |
Winding direction | Record adhesive-side orientation and loading method |
Roll quality | Check flatness, slit-edge cleanliness, roll-end alignment, and telescoping risk |
Sample approval | Trial roll / approved sample for repeat-order comparison |
Protective Film Factory can prepare grades around the actual process. Specify the PE or PET carrier, treatment side, adhesive type, thickness, slit width, roll length, core size, winding direction, color marking, and identification printing. For repeat supply, keep the approved substrate, tested side, dwell period, removal method, and reference sample on record. Before line loading, compare the new roll with the approved sample, review roll-end alignment, and confirm that the winding direction matches the unwinding setup.
Approval should cover more than a resistance value. Check whether the film wets the surface evenly without bubbles, whether edges remain stable after the required dwell period, and whether particle pickup increases during unwinding or peeling. After removal, inspect the surface under suitable lighting for residue, ghosting, or contamination that could affect bonding or lamination. For converted rolls, review flatness, edge cleanliness, telescoping risk, and equipment compatibility.
PE is more flexible and conformable. PET provides better flatness and dimensional stability for precision handling and slitting.
It depends on the anti-static structure. Record the tested side, method, temperature, humidity, and conditioning time before comparing grades.
Yes. Transparent grades allow surface checks, but haze, bubbles, particle pickup, and residue should still be evaluated on the actual substrate.
Surface coating, cleanliness, dwell time, handling route, and removal conditions can change performance. A trial roll helps verify adhesion, static control, edge stability, and clean removal.
